Consumer ratings: Porter-Cable PC250MTK
Ratings
Category: Tools & Home Improvement
Brand: Porter-Cable
Model: PC250MTK
Availability: In Stock. Ships next business day.
List Price :
Discount:
Porter-Cable PC250MTK Consumers Report
Porter-Cable PC250MTK Review by R. Parker (San Diego)
Porter-Cable PC250MTK Review by James
This is one of two of these that has a tool less tool changer. The other is the FEIN oscillating multi tool. This also has 2.5 amps like all the other ones. Granted the dremel one is 1.5 amp and the craftsman one is 2 amps.
Though there are not many third party tool suppliers for this one. It will change it has only been out for two or so months. I am looking forward to getting a few more of the tool attachments, especially the wood rasp attachment.
I testing it out and was surprised how fast it cut the 3/4 pine I had sitting around. It is amazing to make straight plunge cuts. It will be neat to make small mortise and tanner joints.
Porter-Cable PC250MTK Review by R. Mckinnon
I had to install baseboard hot water into a log home. This required removing (squaring) out a section of the bottom logs so the baseboard would sit flush. I decided I needed a multi-cut tool to help with this project. I looked for alternatives to the expensive Fein and found the Craftsman 2.0 Amp Compact A/C Multi-Tool and the new Porter-Cable PC250MTK 2.5 Amp. These are both corded models which I compare below.
Features: The PC comes with a plastic case and the CR with a bag. I like the case better although too many compartments. I like a case with one area for the tool and another large area for attachments. This makes it much easier to shut the case without having to line everything up. The CR comes with a power indicator on the tool and a small built in light which may come in handy. Both tools have an easy to use variable speed dial. The CR has a vacuum port although I found it pretty useless in practice since the suction does not get close enough to the business end. The PC has a more flexible (rubber) power cord than the CR. I bet it would be less stiff in the cold as well. I really liked the quick change system on the PC compared to the hex key on the CR. Since the PC is relatively new the CR has more attachments options. In addition, I believe the CR is compatible with the Fein which has a very large assortment. Due to the quick change system on the PC other manufacturer's accessories will not fit. Besides the connection point on the blades they seem to be very similar in quality from both manufactures. The blades come marked for identification and depth of cut. These marking are painted and wear off just about on first use. Both manuals had very little useful information once you get past the pages of safety instructions. I liked the fact that the CR manual did not come folded like an old map you pulled from the glove compartment. You can actually lay it flat on a table and read it.
Ergonomics: The CR was smaller and felt good in the hand. You could certainly fit it into tighter spaces than with the PC. Vibration in the tools were about the same with a slight edge to the CR which I imagine can be attributed to smaller motor and less angle of oscillation. Both tools have good balance and seem well made.
Performance: The PC is the clear winner here for several reasons. The angle of oscillation and speed of oscillation is greater with the PC. This allows a similar blade to cut faster and the PC did seem to cut faster. My test was plunge cutting to the stops (1.5-2") into a pine log. Note: as you start to penetrate into an interior piece of wood, use GENTLE pressure which will allow the blade to work. If you try to force the tool the blade will stop oscillating with the energy transferring back into the tool; i.e. the tool with shake and it will not cut. In extended runs the PC does not get has hot at the CR. Changing the blade on the CR after an extended run can be a real pain with the hex nut, receiving housing and blade becoming super hot. In addition it takes time to back the hex nut out, install new blade or change angle and re-tighten. On the PC you simply squeeze a spring loaded lever, change blade or adjust angle and release lever to lock in place. Another advantage with the PC's blade change system is the blade stays connected with nothing to loosen. On the CR I found the hex nut to loosen with extended use, especially if you try to force the tool. I am sure this will lead to over tightening and stripping of that hex screw. In the end I kept the PC with the quick change system winning day. I would have given the CR 3 stars. Hope this helps.
More Reviews...
Porter-Cable PC250MTK:: Description
The PC250MTK 36-piece corded oscillating multi-tool kit utilizes a groundbreaking tool free system--just squeeze a lever to release or secure an accessory. This kit is loaded with 35 assorted accessories to allow you to cut, sand, grind, and scrape. The PC250MTK is variable speed and delivers 10,000-20,000 oscillations per minute (OPM) by way of a high-torque 2.5 amp motor that can handle almost any application. The variable-speed unit has an oscillation angle of 2.8 degrees and comes equipped with a 10 cord for easy jobsite maneuverability. The PC250MTK features a durable injection-molded kit box to help keep the tool and accessories organized and protected on and around the jobsite.
Porter-Cable PC250MTK : Limited time only!
Customers Who Viewed This Item Also Viewed
Staub 1102085 Review
AeroGrow 900211-1200 Customer reviews
Fagor 670040380 Reviews
simplehuman KT1135 Customer reviews
Olde Thompson 5050-00 Product review
Porter-Cable PC3013 Product review
Nuby 5361 Review
InterDesign 15162 Reviews
Premium Maxi Locking Wall Mount Mailbox - Black Powdercoat Review
Side Table / Magazine Cabinet with Pullout Tray Product review
Tags : Consumer Report Porter-Cable PC250MTK
Recent posts:
Full Magnussen T1297-73
Discount OmniMount ELEMENTS 503FP low price free shipping
